181-1873-9028

PRODUCT CENTER

HOME >> PRODUCT >>Presence sensing >> ISE101D-24 breathing movement micro-motion human presence sensor
Product Detail

ISE101D-24 breathing movement micro-motion human presence sensor

ѯ
181-1873-9028
Ʒ˵

ϣISE101A-24ǿ絥Ʒ.jpg

1) In vivo detection algorithm, which can carry out mixed detection of movement, twitching and breathing to realize real presence induction


2) Low impedance, high gain anti-antenna design, can effectively resist 5G, WiFi, Bluetooth and other wireless signal interference


3) Remote control design, users can configure the induction parameters according to requirements


4) Support embedded independent installation


5) Five-year warranty






Function

Signal detection instructions: detect people's walking, body movement, head up, turn around and other small movements in normal work and life, as well as breathing signals, and realize the detection of human existence in sleep state.

* Mobile signal: large movement of the body, used for induction trigger


* Fretting signal: sensor real-time detection, indicator light flashing 1;


* Breathing signal: In the absence of micromotion signal, the sensor continuously detects the breathing signal, and the indicator light flashes:


ġDimension drawing (unit: mm)

22.jpg

塢The wiring diagram

23.jpg



Function diagram

24.jpg



ߡInstallation diagram

΢ͼƬ_20220122125013.png

1. The ceiling opening 65-70mm


2. Carefully pry open the button of the rotating protective cover and open it to the maximum state


3. Wiring (note that input and output cannot be inversely connected)


4. Install the crimping tie locking screws and cover the rotary protection cover


5. Bend the spring clamp backward to push the pre-opened hole on the ceiling 6. Ensure the stability and reliability after installation






ˡDetection range

΢ͼƬ_20220122125017.png

Note: Dark color is high sensitivity respiratory heartbeat detection area, middle color is medium sensitivity small motion detection area, light color is low sensitivity large motion detection area.


šFunction Set dip switch

1)Detection Area

΢ͼƬ_20220122125352.png


2) Hold Time

΢ͼƬ_20220122125355.png

Note: The use of sensor function (breath detection) need to set the sensor delay is more than 5S or above


3Daylight Sensor

΢ͼƬ_20220122125358.png

Note: When Disable is set, the sensor turns on whenever it detects movement, regardless of whether there is sufficient light.


4Indicator light 

΢ͼƬ_20220122125401.png

Note: The factory setting indicator is on, which can be turned off by dialing or remote control LS button


ʮRemote control Settings:

΢ͼƬ_20220122125636.png

Switch remote control/DIP switch Settings

1. When the power is off, dial the DIP switch to return to the current dip switch status

2. Dial any remote control Settings to return to the current Settings of the remote control


ʮһInitialize the

The sensor enters the self-test mode for the first time, and the self-test is completed 5 seconds later and the sensor enters the normal working state. During the initialization, neither external movement sensing signal is detected nor remote control signal is received. 


ʮFactory Settings

Sensitivity: : 100%


Delay: 5 s


Optical sensor threshold: Disable


Indicator control: Open


ʮPrecautions for Use

1. The inductor should be installed by a professional electrician. Please power off the inductor before installing, wiring and changing the setting of dip switch


2. The sensor should be far away from large area metal plate, glass and other materials with high density to avoid triggering by mistake.


3. Avoid using objects that vibrate for a long time around the sensor, shaking fans, etc. Vibration signals will be regarded as moving signals to trigger the sensor.


4. There are non-human objects in continuous motion in the induction area, such as animals, continuously swinging curtains, large plants facing the air outlet, etc


5. Product remote control setting after each successful setting, the indicator light flashes 3 times, indicating that the setting is successful.


6. You are advised to turn off the indicator during normal use.


7. Applied to open office with many people, the induction time can be selected as 30s, and the independent office needs to use 1min or more than 3min.


8. Microwave inductor has a certain penetration ability to the building wall, and the microwave penetrating outside the wall may cause false positives when acting on moving objects outside the fortified area. In order to avoid accidental triggering, pay attention to the selection of installation position and appropriate sensing range during installation. For example:


A. When applied in A room with an area of about 5 square meters or smaller, the sensitivity should be set to 25%.


B. When applied in a room with an area of about 10 square meters, the sensitivity should be set to 50%;


C. When applied in a room with an area of about 20 square meters, the sensitivity should be set to 75%;


D. When applied in a room with an area of about 30 square meters or larger, the sensitivity should be set to 100%;


  • Telephone

    • 181-1873-9028
  • Follow wechat

seo seo